410 stainless is a corrosion and heat resistant 12% chromium steel.It is the most widely used of the hardenable stainless steels.Heat treated 410 has mechanical properties comparable to the engineering alloy steel AISI 4130,coupled with the additional benefit of good corrosion resistance.410 is highly resistant to atmospheric corrosion.410S Stainless Steel AK SteelSTAINLESS STEEL TYPE 410Sis a low-carbon,non-hardening ferritic stainless steel.The ability to cool from elevated temperatures without hardening makes Type 410S suited to applications such as annealing boxes,quenching racks,oxidation-resistant partitions and other high-temperature units.Cited by 20Publish Year 2019Author Mahmoud Moradi,Davud Ghorbani,Mojtaba Karami Moghadam,Mahdi Kazazi,Fardin Rouzbahani,Shadi KaraSAE AISI 4340 Steel Properties,Heat Treatment,Equivalent 4340 steel mechanical properties are listed in the following tables. (150 °F),or quench in fused salt at 200 to 210 °C (390 to 410 °F),hold for 10 minutes,and then air-cool to below 65 °C (150 °F).Tempering Hold at 200 to 650 °C (400 to 1200 °F) for at least 1/2 hour; air cooling.The temperature and the time at the temperature
May 16,2013·In its softest condition,type 410 stainless is tough and chips build up on tools.Better finishes are obtained in the cold drawn or heat-treated condition.If higher mechanical properties are required,the material can be machined up to Rc 35.Weldability.Type 410 may be satisfactorily welded.Cited by 8Publish Year 2017Author Masoud Mirzaee,Amir Momeni,Niloofar Aieni,Hamid KeshmiriEncore Metals - T-410,T-410ST-410,T-410S.12% Chromium hardenable martensitic stainless steel.T-410 is the basic chromium grade in the '400' series.It can be treated by conventional means to develop high strength properties with good ductility.In fact,it is in the heat treated condition that T-410 develops its maximum corrosion resistance,particularly when ground Composition Fe/<.15C/11.5-13.5Cr/<1Ni/<1Mn/<1Si/<.04P/<.03SMaterial Stainless Steel - Grade 410 (UNS S41000)PROPERTYMINIMUM VALUE (S.I.)MAXIMUM VALUE (S.I.)UNITS (S.I.)Atomic Volume (average)0.00710.0074m 3 /kmolDensity7.657.85Mg/m 3Energy Content84102MJ/kgBulk Modulus140163GPa 28 rows on azomFe 410 - steel-gradesPhysical Properties of steel grade Fe 410.Temperature.(°C) Modulus of elasticity.(GPa) Mean coefficient of thermal expansion 10-6/ (°C) between 20 (°C) and.Thermal conductivity.(W/m°C)
Jan 05,2017·In this research,the effect of austenitization and tempering on the microstructure and mechanical properties of 410 and 410 Ni MSSs was investigated.The major results are summarized as follows (1) In both steels,austenitization at 900 °C leads to remaining a tempered martensite network on the prior austenite grain boundaries.File Size 2MBPage Count 5410 Steel,Datasheet,Properties,Cross-Reference Table Physical Properties of steel grade 410.Temperature.(°C) Modulus of elasticity.(GPa) Mean coefficient of thermal expansion 10-6/ (°C) between 20 (°C) and.Thermal conductivity.(W/m°C) Specific thermalFile Size 456KBPage Count 2Specification Sheet Alloy 410 - Sandmeyer Steelobtain a wide range of mechanical properties.The alloy has good corrosion resistance along with high strength and hardness.In the annealed condition 410 is ductile and may be formed.It remains magnetic in both the annealed and heat treated conditions.
Jul 30,2019·In this research,Nd:YAG laser is used to improve the surface hardness of AISI 410 martensitic stainless steel.The effects of Focal point position,scanning speed and pulse width on hardness,the geometrical dimension of the hardened zone,metallographic phases,and corrosion behavior of laser hardened sample in 3.5 wt% NaCl solution were studied.Properties Stainless Steel - Grade 410 (UNS S41000)28 rows·410 is the basic martensitic grade stainless steel.They are optimised for high hardness,Related searches for 410 steel mechanical properties410 steel propertiesstainless steel 410 properties410 stainless steel properties chartphysical properties of steelstainless steel grades and propertiessteel alloy properties chart12345Next
Physical Properties Melting Point 2729°F / 1495°C; Density 0.276 lb/in 3 / 7.65 g/cm 3; Specific Graivy 7.65; Modulus of Elasticity in Tension 29 X 10 6 psi / 200 GPa; Mechanical Properties Temper Annealed; Tensile Strength Minimum (psi) 65,000; Yield Strength Minimum 0.2% offset (psi) 30,000 % Elongation in 2 Minimum 20%; Hardness Rockwell B80Stainless Steel - Grade 410 (UNS S41000)IntroductionKey PropertiesCompositionMechanical PropertiesPhysical PropertiesGrade Specification ComparisonPossible Alternative GradesCorrosion ResistanceHeat ResistanceHeat TreatmentGrade 410 stainless steels are general-purpose martensitic stainless steels containing 11.5% chromium,which provide good corrosion resistance properties.However,the corrosion resistance of grade 410 steels can be further enhanced by a series of processes such as hardening,tempering and polishing.Quenching and tempering can harden grade 410 steels.They are generally used for applications involving mild corrosion,heat resistance and high strength.Martensitic stainless steels areSee more on azomEstimated Reading Time 4 minsPublished Oct 23,2001410 Stainless Datasheet - upmetType 410 is hardenable,straight-chromium stainless steels which combine superior wear resistance of high carbon alloys with the excellent corrosion resistance of chromium stainless steels.Oil quenching these alloys from temperatures between 1800°F to 1950°F (982-1066°C) produces the highest strength and/or wear resistance as well as corrosion resistance.Type 410 alloy is used where strength,TECHNICAL DATA SHEET·Recently,the 410-3Ni3Mo martensitic stainless steels have been developed with improved pitting resistance and better mechanical properties compared to standard 410 steels [6,7].The addition of Mo is suggested to increase both pitting resistance and strength,while Ni improves toughness and avoiding ï ¤-ferrite due to high amount of Mo.
File Size 1MBPage Count 3AK Steel Type 410 is a martensitic stainless steel that provides excellent corrosion resistance plus high strength and hardness.It is magnetic in both the annealed and hardened conditions.A wide range of properties can be developed with different heat treatments.Applications requiring moderate corrosion resistance and high mechanical properties are ideal for this alloy.AISI 410 Stainless Steel Properties,SS410 Heat Treatment 13 rows·Jun 21,2020·Mechanical Properties.AISI 410 stainless steel mechanical properties are given in the